> Shop by Product > Electrical >

Fuzeblock FZ1
Fuzeblock FZ1

Alternative Views:

Our Price: $119.00
You'll earn 100 points

Stock Status:In Stock

Product Code: FUZEBLOCK


Fuzeblocks FZ-1 is a fuse block that is easy to install and fits into a very small space. The on board relay offers the choice for any device to be switched on or off automatically with the vehicle or to be powered constantly.

With the FZ-1 in place, you can power all kinds of motorcycle accessories including, but not limited to, auxiliary lighting, GPS, radar detector, CB/FRS/GMRS radio, heated grips, XM radio, audio mixers, intercom system and any other device requiring 10 Amps or less. Any of these accessories can have constant or ignition-switched power by simply placing the fuse in the correct position for the power desired.

The simplified installation for the FZ-1 fuse block requires no crimping. All connections are made by heavy duty screw terminals that can accept up to a 12 gauge wire. All the FZ-1 needs is +12VDC, a ground connection and a +12VDC switched source to make it fully functional. The unique board layout provides six individually fused circuits that can supply constant or switched power for each accessory depending on your needs.


The FZ-1 one was designed to make installation simple and quick. The FZ-1 uses screw terminals for all its connections so that it requires no crimping. The installation is as simple as 1-2-3.


1. Disconnect the negative lead of the battery. Then remove the cover and mount the FZ-1 being sure that the back of the FZ-1, with the exception of the mounting posts, do not come into contact with metal or ground.

2. Connect a 12 gauge wire from the +12VDC input (J1) to the positive terminal of the battery. Make sure to install an in-line fuse somewhere along the wire as close to the battery terminal as possible.

3. Connect a 12 to 18 gauge wire (18 gauge is usually more than sufficient) from the +VT input (J1) to a switched power source on the vehicle. A switched power source is a wire that is +12 VDC when the vehicle is on and 0 VDC when the vehicle is off. Refer to your service manual, local mechanic and/or internet forum to find a suitable switched source for your particular vehicle and for the best procedure on tapping the wire. The switched source is used to energize the FZ-1's relay coil (about 1W) which will cause the relay contacts to close and supply +12VDC from the battery to the switched +12V output bus.

4. Connect a 12 gauge wire between the GND input (J1) and the negative terminal of the battery.

5. Insert the proper amperage fuse, for your device, into either the switched or constant fuse position on one of the 6 output circuits. Then connect the positive wire for your device to that circuit's output terminal (J2/J3).

6. Connect the ground wire for your device to the ground bus (J4/J5).

For ease of installation, simply purchase the optional fuzeblock wiring kit.

Due to the sinking Canadian dollar we have had to raise the Fuzeblock pricing to reflect the currency exchange.

You will earn 100 reward points when purchasing this product, to put towards future purchases.

Fuzeblock FZ1 wiring harness
Our Price: $45.00

Fuzeblock FZ1 wiring harness

Average Rating: 5 of 5 Total Reviews: 34 Write a review »

  0 of 0 people found the following review helpful:
Fuzeblock FZ1 purchase & install August 6, 2019
Reviewer: Patrick McKay from Vancouver, BC Canada  
After reading numerous positive reviews, I can now add my own. I have next to zero knowledge or skill with anything electrical, but was able to successfully complete the installation on my 09 V-Strom 650. Having just installed a set of Denali DR1's, I suppose I felt some confidence in undertaking this without resorting to a moto shop. It turned out to be very simple, and straightforward. 👍

Was this review helpful to you?

  0 of 0 people found the following review helpful:
4th one I bought May 9, 2019
Reviewer: Bishop from Toronto, ON Canada  
I love them so much I bought more for my motorcycles and cars.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
Easy way to get rid of wires off of batt terminal March 29, 2019
Reviewer: .doug mccartney from Coldstream, BC Canada  
Easy to hook up to ignition switch.  Now can hook up all your accessories to a fused block which is turned off or on by the ignition switch.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
Fuzeblock February 18, 2019
Reviewer: stephen Staines from Perth, ON Canada  
Quality look and feel to the product. Easy installation. Works as advertised. If it were 20$ cheaper, it would be a 5 out of 5.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
FUZEBLCOK FZ1 and wiring July 14, 2018
Reviewer: G Rousseau from Anjou, QC  
Glad I check with MI. Good product at a great price. Ordering easy, quick delivery, website easy to navigate and product as advertised. No issue with installation and fits well under my seat (V-Strom 650). Now I can add more electric devices!

Was this review helpful to you?

View All Customer Reviews