The new Go Cruise throttle control is an amazingly clever, simple and brilliant solution to relieving stress on your wrist on long rides, and is the least expensive "Cruise Control" for motorcycles on the market!
Go
Cruise installs on your throttle grip in a few seconds, no tools needed.
When you're at your desired speed, push the Go Cruise down with your
index finger until it rests on your brake lever. Go Cruise has just
enough grip to hold your throttle in place and take stress off your
wrist. To reduce speed, simply roll the throttle off manually to
override the Go Cruise.
It's that simple!
-
One of the best on the market
-
Easy to use - on/off in 6 seconds
-
Design for the original stock RUBBER grip
-
22 mm (Small, 7/8" Dia. Handlebar size) for urban and sport bikes
-
25 mm (Large, 1" Dia. Handlebar size) for Harley Davidson or cruisers
-
Super EZ to install, no tool required
Comes with silicone ring, which is ideal for metal grip or increasing friction.
WARNING
Improper installation and/or use of the throttle control could result in serious injury or death,
as is the case with any other motorcycle specific part or accessory.
1. DO NOT take your hands off the handlebars.
2. DO NOT use in traffic.
3. DO NOT use in congested residential or urban areas.
4. DO NOT use when precise speed changes are required.
5. DO NOT use if you are an inexperienced rider.
6. DO NOT use with any other cruise control device.
7. DO NOT use until you are thoroughly familiar with the operation of the throttle control.
8. Disengage Go Cruise Throttle Control in downhill.
FAQ
Q. The package come with a silicone ring, What’s it for?
Each order come with one silicone ring.
It is ideal for aftermarket chrome grips, or to increase the friction for your OEM grips.
Q. What size of Go Cruise should I use for my bike？
Go Cruise designs based on handlebar size, not grip size. There are two different size of handlebars on the market.
1. 7/8” handlebar (22mm) for sports bikes and urban bikes.
Or fit grips diameter from 1.18” ~1.34” (30 mm ~ 34 mm)
2. 1” handlebar(25mm) for Harley and cruiser bikes.
Or fit grips diameter from 1.38” ~ 1.53” (35 mm ~ 39 mm)
If you grip size is less than 1.18”(30 mm) you need to order extra ring.
Or use electrical tape around 2-3 layers on the grip to increase the
diameter up to 30mm, then put silicone rings top over electrical tape.
If you grip size over 1.55” (39 mm) do not buy it.
Q. Can Go Cruise fit on my KURYAKYN ISO grips?
Yes, the large Go Cruise (for 1”bar) can fit on ISO grips perfectly.
Q. What kind of grip can’t use Go Cruise throttle control？
Go cruise can fit on 99% stock OEM rubber grips, metal (chrome) grip as well.
Won't work on any aftermarket foam grip and 100% super soft silicone grips.
(It fits those covers that slip over your existing grips, such as Grip Puppies.)
Q. I have Grip puppies on my OEM grips, can I use Go Cruise?
For using on Grip Puppies we suggest 3 options.
1. The best way to do is to set Go Cruise on rubber grip first, then install
Grip Puppies.
2. Move Grip Puppies to the right to make room for silicone ring
and Go Cruise (about 1/4" width), then install Go Cruise.
3. If you can not move the Grip Puppies to make room for Go Cruise.
Cut 1/4" Grip Puppies to make room for silicone ring and Go Cruise.
Q. Can Go cruise fit on my Driven D3 sports bike grips?
Sorry, It won’t work on D3 grips.
Because Go Cruise need 3/8” flat surface on left side of grip (need room for silicone ring)
D3 sports bike grips only have 1/4" flat surface, so you can’t use Go Cruise.
Q. My Go cruise does not hold the speed?
If you go cruise does not hold the speed after a few months, most
likely because Go Cruise gets dirty from the ride. First remove Go
Cruise and silicone ring, use soap and water to clean them, then put
them back on the grip. Most of time will solve the problem.
Do not use any chemical to clean Go Cruise and silicone ring。
Q. What about warranty?
We warrants to the original purchaser that the throttle control is
free of material and workmanship defects for one year from the date of
purchase.
Q. Not working on my KLR Endure 650?
Some of KAWASAKI KLR 250/650 have dirt bike grips, the diameter size
of the grip is less than 29mm. The only way to use Go Cruise on your
bike is to use electrical tape go around the grip about 3 to 5 layers to
increase diameter(up to 30mm), then put on silicon ring over.(silicone
ring come with package). That should do the work.
Or we can refund your money.
Q. What's Go Cruise made off？
Go Cruise is made of composite material which can work as low as 5°F (-15℃) and up to 167°F (75℃) strict environment.
Go Cruise 
